0
£0.00
British Sterling
Free Delivery Same Day Dispatch Largest Guitar Part Source
Floyd Rose Special Locking Tremolo With Locknut

Floyd Rose Special Locking Tremolo With Locknut

  code:n/a
  • Offers Available
  • Free UK Delivery when you spend £25.00 Online
From £107.95
Item in Stock  |  Usually dispatched within 24 hours
Add to Bag
This product has been added to your basket...
  • Continue Shopping
  • Checkout

The Floyd Rose Special is the authentic version of a licensed Floyd Rose tremolo system manufactured in Korea exclusively for Floyd Rose. The Floyd Rose Special maintains the construction parameters and features of an Original Floyd Rose, while utilizing zinc alloy saddles in place of steel and a zinc alloy sustain block in place of brass. The design specifications and high quality materials of the Special Series Floyd Rose bridge will hold up to the demands of today's performers. 

 

Choose between an S2 or S3 nut:

 

Nut Sizing Chart
Nut Width Radius Height at D E to E Centre String Spacing Bullet Recess
SR2 1.653 in.(42mm) 12 in.
(300mm)
.236 in.
(6mm)
1.437 in.
(36.5mm)
.287 in.
(7.3mm)
No
SR3

1.692 in.(43mm)

12 in.(300mm) .236 in.
(6mm)
1.437 in.
(36.5mm)
.287 in.
(7.3mm)
No

 

 

FLOYD ROSE SPECIAL TREMOLO - STRING CHANGING INSTRUCTIONS

Step 1:
Unlock the three clamps at the nut with the 3mm allen wrench provided with the guitar or bridge.
Step 2:
Set the fine-tuners on the bridge to the middle of there tuning range.
Step 3:
Change one string at a time (starting at either E string) by first loosening the string and unclamping it at the saddle with the 3mm allen wrench.
Step 4:
Cut the ball end off the replacement string with a pair of wire cutters.
Step 5:
Place the freshly cut string end into the center of the saddle and tighten the clamping screw until it is difficult to turn.
Step 6:
Thread the other end of the string under its nut clamp and under the string hold down bar, then to the tuning key and tune the string. [Pull on the string until it is tight around the tuning key and retune.]
Step 7:
Repeat 2 through 5 until all strings are replaced.
Step 8:
Check your tuning on all strings once again. 
Step 9:
Re-clamp the three nut clamps.
Step 10:
Check your tuning once again making any adjustments this time with your fine-tuners only.
 

FLOYD ROSE SPECIAL TREMOLO - STRING TUNING INSTRUCTIONS

Tuning your Floyd Rose bridge is certainly a tricky business when the bridge is floating. This is because the total tension of the strings must balance the total tension of the tremolo springs with the base plate of the bridge parallel to the face of the guitar and with the strings tuned to the desired pitch. So, follow these steps and and it will start to make sense.
Step 1:
Loosen the three string clamps at the nut
Step 2:
Set your fine tuner screws on the bridge to the middle of their adjustment range.
Step 3:
Tune the strings to your desired pitch (this can be drop tuning, open tuning, or standard pitch, the procedure is the same for any tuning) with an electronic tuner starting with the low ‘E’.
Step 4:
When you have finished tuning all of the strings, check the tuning on the low ‘E’ again. If the low ‘E’ is now flat, re-tune the strings starting again with the low ‘E’ but this time tune the E, A, D, G, and B strings a little bit sharp, then the high ‘E’ to pitch. If the low ‘E’ is sharp, re-tune as just described only tuning the first five strings a little flat. You must tune the strings a little sharp or flat to get to your tuning because every time you change the tension (or pitch) of one string, the other strings change pitch in the opposite direction. 
Step 5:
Repeat step 4 until all the strings are at the desired pitch.
Step 6:
When the strings are at the desired pitch, check to see if the bridge base plate is sitting parallel with the top surface of the guitar. If the base plate is tilted forward away from the body, you must tighten the tremolo springs tension by turning the spring claw screws clockwise and repeat step 4. If the base plate is tilted back toward the body, you must loosen the tremolo springs tension by turning the spring claw screws counterclockwise and repeat step 4. [Step 6 only needs to be done on initial setup of the bridge or if you change to another gauge of strings or change to a different tuning.]
Step 7:
When the bridge is sitting parallel to the face of the guitar and the strings are tuned to the desired pitch, re-clamp the three nut clamps and re-tune (if necessary) once again using only the fine tuners.
Step 8:
When tuning is complete, check the action of the strings off the neck. If your action is to high or to low, adjust the action with the two rocker screws (bridge pivot screws) using the 3mm Allen wrench. This adjustment will slightly change your tuning. If your fine tuners run out of range you must repeat steps 1 through 7.


FLOYD ROSE SPECIAL TREMOLO - INTONATING YOUR BRIDGE

[note - before intonating your bridge you must tune your guitar using the tuning instructions above]

Step 1: Tune all the strings on your guitar to an electronic tuner with all the nut clamps released.
Step 2:Determine if the intonation of the string you wish to change is sharp or flat by chiming the string directly over the 12th and checking the tuning. Then, carefully press the string down to the 12th fret and check the tuning again with the string fretted. If the fretted note is flat when compared to the chimed note, then the saddle must be moved toward the nut until the chimed note and the fretted note match. If the fretted note is sharp when compared to the chimed note the saddle must be moved away from the nut until the chimed and fretted notes match.

To move the saddle:
Step 1:
Once you have determined which direction (toward or away from the nut) to move the saddle, loosen the string until it is limp.
Step 2:
Loosen the attachment screw holding the saddle to the bridge plate while holding the saddle in place. Move the saddle in the desired direction a small amount (about 1/16in on the first adjustment and your best guess on subsequent adjustments) and re-tighten the screw. [Note: If the saddle will not move forward because it is resting against the attachment screw, you can move the screw to the next hole forward on the bridge plate. This will give you more adjustment range. Also, if you need to move the saddle away from the nut to a position where the attachment screw can no longer clamp the saddle firmly, you can move the screw to the next hole back on the bridge plate.]
Step 3:
Re-tune the string and check the intonation again using the procedure outlined above (check the intonation).
Step 4:
Repeat this cycle until each string is properly intonated.
When you’re finished with the intonation procedure re-tighten the nut clamps. This will not change your intonation setting.

 

Delivery:

Any order placed before 3.00pm on a working day will generally be sent the same day. If the order is placed after 3.00pm on a weekday or anytime during the weekend or a public holiday we will send the order the next working day.

We offer "Royal Mail First Class Standard Post" and "Registered Next Working Day" for orders shipping to an address located within the United Kingdom and "Registered International Post" for any orders that ship outside of the United Kingdom - please click here for further details.

Returns:

If you need to return a product purchased from W.D. Music UK, please notify us in writing (email/letter) within 14 working days and then return the item to us within 28 working days in order to receive a full refund without the original delivery charge.  The cost of returning the item to W.D. Music UK is not included unless the return is due to missing or faulty parts. 

The returned goods must be in a re-saleable state and any goods or accessories that accompany the returned product must also come back to us. The goods should also be returned with their original box, packing and accessories. Please click here for further details.

We offer two payment gateways on our website - SagePay and Paypal.

SagePay accepts all major credit and debit cards. All transaction information passed between the WD Music and Sage Pay system is encrypted using 128-bit SSL certificates. No cardholder information is ever passed unencrypted and any messages sent to our servers from Sage Pay are signed using MD5 hashing to prevent tampering. You can be completely assured that nothing you pass to Sage Pay’s servers can be examined, used or modified by any third parties attempting to gain access to sensitive information.

When you pay with Paypal, all information is protected by SSL with an encryption key length of 168 bits (the highest level commercially available). Your personal information is stored on Paypal's servers and heavily guarded, both physically and electronically. To further shield your credit card and bank numbers, Paypal do not directly connect their firewall-protected servers to the internet.